Tightenthe bolts to 15 Nm (11 lb-ft). Tighten the bolts to 45 Nm (33 lb-ft). Turn the bolts 90 degrees. Turn the bolts an additional 90 degrees. NOTICE: Install the camshafts with the alignment slots in the camshafts lined up so the Camshaft Alignment Plate can be installed without rotating the camshafts. anychance anyone can assist with torque specifications for the main and big end Crankshaft bearings as well as the stock cylinder head bolts please? I have used Installthe main bearing caps in the order indicated in the figure. Tightening torque: (1) 44—46 N·m {4.5—4.6 kgf·m, 32.5—33.9 ft·lbf} (2) 175°—185°. Cylinder Head Bolt Assembly Note. 1. Tighten the cylinder head bolts in the order indicated in the figure in six steps. (1) Tighten to 5.0 N·m {51 kgf·cm, 44.3 in·lbf}.
TheVIN# XXXXX XXXXX. Hello again, I hope the following helps. The torque for the cylinder head bolts is as follows. Stage 1: Tighten bolts 1 through 10 to 40 Nm. Stage 2: Tighten the front two (M8) bolts to 15 Nm. Stage 3: Tighten the front two (M8) bolts to 45 degrees. Stage 4: Tighten bolts 1 through 10 to 120 degrees.
FordRanger 3.2 Duratorq engine Main Bearing Bolt torque Step 1 = 15 Nm, 11 2 = 20 Nm, 15 lb.ft Step 3 = 35 Nm, 26 lb.ft Step 4 = 80 Nm, 59 lb.ft Step 5 = +90 degrees. Ford Ranger 3.2 Duratorq engine Cylinder Head Bolt torque Step 1 = Bolts 1 to 12: 10 Nm
Hereare the torque settings for a Ford Fiesta 1.4 2010 for the main bearings, head bolts, and big ends: Main bearings. Main bearing caps: 1st stage - 7 Nm, 2nd stage - 16 Nm. Main bearing bolts: 45 Nm + 90°. Head bolts. Cylinders 1-3: 2nd stage - 30 Nm + 90°, 3rd stage - 80 Nm + 180°. Cylinder 4: 2nd stage - 25 Nm + 90°, 3rd stage - 60
JuniorBuilder Posts 73 Registered 27/10/11 Location 1 Member Is Offline Photo Archive Building: posted on 16/9/13 at 08:02 PM. Duratec head bolts torque settings Hi guys, I need the torque setting for standard head bolts for 2.0L duratec. I do have the build manual but have my memory stick at work! Doh. Thanks Mike. big-vee-twin. rrho.
  • v779wj6bfk.pages.dev/210
  • v779wj6bfk.pages.dev/32
  • v779wj6bfk.pages.dev/768
  • v779wj6bfk.pages.dev/118
  • v779wj6bfk.pages.dev/223
  • v779wj6bfk.pages.dev/519
  • v779wj6bfk.pages.dev/755
  • v779wj6bfk.pages.dev/181
  • v779wj6bfk.pages.dev/13
  • v779wj6bfk.pages.dev/935
  • v779wj6bfk.pages.dev/933
  • v779wj6bfk.pages.dev/424
  • v779wj6bfk.pages.dev/954
  • v779wj6bfk.pages.dev/833
  • v779wj6bfk.pages.dev/241

    • 2.0 duratec engine torque settings